Microprocessor & Microcontroller Trainers and Interface Modules
Microprocessor Trainer
86/88E:
16 bit 8086 based low cost Microprocessor Trainer with on-board RS-232-C port, USB port, 20X4 LCD, PC keyboard connector and Windows / DOS driver.
86/88-2:
16 bit 8086 based Microprocessor Trainer with on-board keypad, 8 digit seven segment display, RS-232-C and Windows / DOS driver.
86/88-3:
16 bit 8086 based advanced Microprocessor Trainer with on-board DAC, RS-232-C port, 20×4 LCD, PC Keyboard connector, Windows / DOS driver and provision for ADC, RS 485, etc.
85 A:
8 bit 8085 based Advanced Microprocessor on-board EPROM Programmer, Keypad, seven segment display, printer port, RS-232-C port, USB port, built-in Editor, Assembler and Disassembler.
MPS 85-3:
8 bit 8085 based Microprocessor Trainer with on-board keypad, seven segment display, RS-232-C, battery backup for RAM, Windows / DOS driver, built-in Editor, Assembler and Disassembler Trainer
Microcontroller Trainer
REV 51:
8 bit 8051 based advanced Microcontroller Trainer with on-board DAC, RS-232-C port, 20X4 LCD, PC keyboard connector, Windows / DOS driver and provision for ADC, RS 485, etc.
REV31:
8 bit 8051 based Microcontroller Trainer with on-board keypad, 7 digit seven segment display, printer port, Rs-232-C port and Windows / DOS driver.
REV51E:
8 bit 8051 based low cost Microcontroller Trainer with on-board RS-232-C port, USB port, 20X4 LCD, PC keyboard connector and Windows / DOS driver.
REVMCB51:
Single Chip MCU Trainer Based on 89C51Rx2 and supports on-board programming & Integrates with Keil IDE µVision3
PIC Trainer
REV PIC 01:
PIC 16F876 based Microcontroller Trainer with on-board RS-232-C, provision to debug, programming via RJ11 cable using ICD 01.
REV PIC 02:
PIC 16F876 based Microcontroller Trainer with on-board RS-232-C, 16X2 LCD, 4 digit seven segment display, I2C, Relay and provision to debug, programming via RJ11 cable using ICD 01.
REV PIC 03:
PIC 16F877 based Microcontroller Trainer with on-board RS-232-C,6 digit seven segment display, 10 bit ADC, provision to debug,programming via RJ11 cable using ICD 01. Compatible with common GSAS Interface Modules.
In-Circuit Debugger
NAX ICD 01:
In-circuit debugger and In-circuit Serial programmer for PIC 01, 02 &03 Trainers using MPLAB IDE.
Interfacing Modules
IF -8251/8253*:
8251/8253 Study Card Interface.
IF – 8255*:
8255 Study Card Interface.
IF – 8259*:
8259 Study Card Interface.
IF – 8279*:
8279 Study Card Interface.
IF -8ADC 12M:
12 bit ADC Interface with 8 Channel MUX 10 µsec, using AD1674.
IF – 16 ADC 8:
16 Channel 8-bit ADC Interface using ADC0816.
IF-DADC:
DAC for ADC & Temp.Sensor Interface.
IF -DDAC:
Dual DAC Interface.
IF -DIS:
4 – Digit, Seven Segment LED Display Interface.
IF – DSADC:
Dual Slope ADC Interface.
IF- ELV:
Elevator Interface.
IF – KBD:
Calculator Type Keyboard Interface.
IF – HEX KPD:
4X4 Matrix Hex Keypad Interface.
IF – LC:
Logic Controller Interface.
IF – LCD:
16X2 LCD Interface with backlit.
IF – MTG:
Musical Tone Generator Interface.
IF – µP24*:
24 Column Dot Matrix Printer Interface with Epson M180 Printer Mechanism.
IF – OPTIN:
Opto Isolated Input Interface.
IF – OPTOUT:
Opto Isolated Output Interface.
IF – PGMR*:
EPROM Programmer Interface (2716 through 27512).
IF – RLYO:
Relay Output Interface.
IF – RTC:
Real Time Clock Interface (with battery backup).
IF – STEP:
Stepper Motor Interface with Stepper Motor (3Kg/cm, 5V DC) & Power Adapter.
IF – TRL:
Traffic Lights Interface.
IF – TXDR ADC:
TXDR Interface using ICL7109A and RTD, PTI00 with 2 wire configuration.
IF – DC MOTOR:
DC Motor Interface with DC Motor and RPM sensor.
IF – KBD – DISP:
4X5 Matrix Calculator style keyboard and 6 Digit, 7 Segment Display Interface.
